• Best /CRI1 Owners Manual Garage Door Opener Model 139.53626SR Model 139.53515SR FASTEN THIS MANUAL NEAR THE GARAGE INSTALLATION. PERIODIC CHECKS REQUIRED TO INSURE SATISFACTORY FOR RESIDENTIAL USE ONLY. FTSMRN - I/2HP CONTENTS - I/2HP Safety Rules. Operation Maintenance Features of Your Opener. • Start By Reading These Important THIS SAFETY ALERT SYMBOL MEANS CAUTION -- PERSONAL SAFETY OR PROPERTY DAMAGE INSTRUCTION, THIS GARAGE DOOR OPENER IS DESIGNED AND TESTED TO OFFER REASONABLY SAFE SERVICE PROVIDED IT IS INSTALLED AND OPERATED IN STRICT ACCORDANCE WITH THE FOLLOWING SAFETY. • If the chain returns to the position described and illustrated in Step 5 page 9, DO NOT make ANY further adjustments.

TRANSMITTER: than one garage door opener, if desired. The other push but- TO CORRECT tons may also be used to operate 53000 and 53000SR Series tight controls. • Limit device. Limit adjustment. Start circuit. Length (overall). Headroom required.

Sears Craftsman 1/2 HP Garage Door Opener. How to Adjust Force on a LiftMaster Garage Door Opener with Manual Adjustment. Craftsman Garage Door Openers from Sears Garage. View and Download CRAFTSMAN 139.53910D owner's manual online. 139.53910D Garage Door Opener pdf manual download. 315Mx= GARAGE. For Sears professional.

2 inches Hanging weight. For your garage door opener.

They are illustrated below with sears stock 7 53776 BRACKETS: The trolley halves reconnect. • CARTON CHECK LIST SEARS has packaged your GARAGE DOOR OPENER In two cartons which contain all the parts and hardware Illustrated below and on Page 22. Hasler Printer Drivers. Co_r SEPARATE ALL HARDWARE FOR ASSEMBLY AND INSTALLATION ASSEMBLY HARDWARE l_readed Trolley Rod Lock'washer 5/16'. • Tee Rail (End Se_on) SquareCarriage Cablepulley bracket attaches toFRONT ENDofteerail RAIL FRONT (TO DOOR) DO NOT RUN THE GARAGE DOOR OPENER UNTIL INSTRUCTED Tee Rail & Attach Cable TEE RAIL BACK Tee Rail (End Section) 1/4' Lodx Nut Br_.

Rail PROCEDURE: surface for assembly. • Assembly AS A TEMPORARY STOP, INSERT A SCREWDRIVER INTO HOLE IN FRONT END OF TEE RAIL AS SHOWN.

Attach threaded sha_ to trolley with Iockwasher as shown. Slide trolley assembly along rail to screwdriver stop, NOTE: If trolley hits against the nut on Tee rail, center section was attached from wrong side and must be repositioned.

• Assembly STEP 4 DO NOT REMOVE CHAIN AND CABLE FROM CARTON. Detach cable from side of carton. Remove master links from coin envelope.

MASTER LINK PROCEDURE: Insert pins of master link bar through cable loop and hole in front end of trolley (A) as shown. • Troll_ Base of Tee Rail ASSEMBLY OF YOUR GARAGE DOOR OPENER IS NOW COMPLETE. BEFORE YOU PROCEED WITH THE INSTALLATION OF YOUR GARAGE DOOR OPENER, ALL SAFETY RULES.

KEEP GARAGE DOOR BALANCED. STICKING OR BINDING DOORS MUST BE REPAIRED. THE GARAGE DOOR. • Installation Position and Install Header Bracket STEP 1 Installation instructions THE HEADER BRACKET MUST BE RIGIDLY FASTENED TO THE HEADER WALL. REINFORCE THE WALL WITH A 2x4 IF NECESSARY.

FAILURE TO COMPLY MAY RESULT IN IMPROPER OPERATION OF SAFETY REVERSE SYSTEM (SEE PAGE 18). • Installation STEP Header Bracket Cle_s Pin 5/16'x2-3/4' STEP 3 Position Follow only those instructions TO PREVENT DAMAGE TO ALL LIGHTWEIGHT THE OPENER ON THE DOOR. INSTALLATION SECTIONAL & ONE-PIECE DOOR WITH TRACK NOTE: A 2x4 is convenient for setting to-Tee rail distance. It is not necessary where headroom is insufficient. • Installation THE OPENER CHASSIS MUST BE SECURELY FASTENED TO A STRUCTURAL Three representative Installations or crossed (Fig.2) to provide rigid support, On finished ceUings (Fig.3), attach a sturdy metal bracket (not supplied) to ceiling joists before installing opener. PROCEDURE: On EACH side of the opener measure the distance from chassis to the structural supports.

• A convenient place is beside the service door and OUT OF REACH OF CHILDREN. Run the bell wire up the wall and across the ceiling to the garage door opener. Use insulated staples.

Livro Purga Em Angola Pdf Printer. Canon Easy Photoprint Windows Xp. The receiver terminals as well as the antenna ere located k Wall Control on the right side panel of the opener. • Installation STEP 7 Make sure antenna wire is bent down before installing lights and lenses.