Errors and warnings are displayed by the following ways: – Operator call errors are indicated by the Alarm LED lit in orange, and the error and its solution are displayed on the LCD. – Messages during printing from a computer are displayed on the MP driver Status Monitor. – Error codes are printed in the “operator call/service call error record” area in EEPROM information print. Buttons valid when an operator call error occurs: – ON button: To turn the machine off and on again. – OK button: To clear and recover from an error. In some operator call errors, the error will automatically be cleared when the cause of the error is eliminated, and pressing the OK button may not be necessary. – Stop button: To cancel the job at error occurrence, and to clear the error.

Hp Psc 2170 User Manual. How to repair the Epson T13 printer that cannot turn ON but the power supply unit not broken indicated by the out voltage from the power sup.

Operator Call Error (Alarm LED Lit In Orange) Error Error code 7-segment LCD Solution No paper in the rear tray. [1000] E02 Set the paper in the rear tray, and press the OK button. [1300] E03 Remove the jammed paper, and press the OK button. Paper output tray open.

[1251] E03 There may be an obstacle in front of the machine. Remove it, if any, and press the OK button. Ink cartridge not installed, or not properly installed.

[1401] E05 Install the ink cartridge properly. If the error is not cleared, the ink cartridge may be defective. Replace the ink cartridge. Ink cartridge temperature sensor error.

Download Driver Hp Laserjet 1010 Windows 8 64 Bit. [1403] E05 Re-set the ink cartridge. If the error is not cleared, the ink cartridge may be defective.

Replace the ink cartridge. Non-supported ink cartridge is installed. [1485] E05 A non-supported ink cartridge is installed. Install the supported ink cartridge.

If the error is not cleared, the ink cartridge may be defective. Canon 1210 Driver Win 7 64bit here. Replace the ink cartridge.

Ink cartridge in a wrong position. [1486] E07 Install the ink cartridge in the correct position. If the error is not cleared, the ink cartridge may be defective. Replace the ink cartridge.

Multiple ink cartridges of the same color installed. [1487] E07 Confirm that each ink cartridge is installed in the correct position. If the error is not cleared, the ink cartridge may be defective. Replace the ink cartridge. Ink cartridge hardware error [1682] E15 Re-set the ink cartridge. If the error is not cleared, the ink cartridge may be defective.

Replace the ink cartridge. Ink cartridge not recognized. [1684] E14 A non-supported ink cartridge is installed. Install the supported ink cartridge. The remaining ink amount unknown. [1686] E13 Replace the ink cartridge. Printing with an empty ink tank can damage the machine.

To continue printing without replacing the ink cartridge, press the Stop/Reset button for 5 sec. (After the operation, it is recorded in the machine EEPROM that the function to detect the remaining ink amount was disabled.) Ink cartridge not completely installed. [1687] E04 Re-set the ink cartridge. If the error is not cleared, the ink cartridge may be defective. Replace the ink cartridge. [1688] E16 Replace the ink cartridge. Printing with an empty ink tank can damage the machine.

To continue printing without replacing the ink cartridge, press the Stop/Reset button for 5 sec. (After the operation, it is recorded in the machine EEPROM that the function to detect the remaining ink amount was disabled.) Warning: The ink absorber becomes almost full. [1700] E08 Replace the ink absorber, and reset the ink absorber counter. Pressing the Stop/Reset button will exit the error, and enable printing without replacing the ink absorber. However, when the ink absorber becomes full, no further printing can be performed unless the applicable ink absorber is replaced. Service Call Error (Cyclic Blinking in Orange (Alarm LED) and Green (ON LED). Cycles of blinking in orange and green Error Error code 7-seg.

LCD Conditions Solution (Replacement of listed parts, which are likely to be faulty) 2 times Carriage error [5100] P02 An error occurred in the carriage encoder signal. 1) Confirm that no foreign material is in the area where the carriage moves. 2) Clean the timing slit film. If it cannot be cleaned, replace it.